For obvious reasons running speaker wire is easiest to do earlier the dwelling theater room is finished; earlier the drywall goes up specifically.

This way you can run wire to the locations they need to exist behind the wall surfaces and continue all that ugly cable out of sight.

running speaker wire

That beingness said, this is not e'er possible, then we have to focus on other efficient means to get your speaker wire to the speakers.

One such solution is to utilise a fish tape, cut a small-scale slit into the carpet and run flat speaker wire nether the carpet.

Running speaker wire under carpet is a lot easier than vehement off the drywall or fishing cable through the attic in most cases.

But y'all cannot or should not just run whatever wire under the carpeting. For one matter most speaker wire will create a lump where the wire is run.

In some situations this is not such a big bargain, just in near installations you would benefit from using a purpose congenital cable that is designed to be walked on and is also very flat.

The jacket on this cablevision is stronger and built for the abuse of being treaded on solar day in and twenty-four hour period out. Plus, information technology'south basically unnoticeable to the heart as well, which is an added bonus.The other style is to run the cable into the crawl infinite if yous have one (a crawl space) or basement or even the attic. In this situation yous will have to drill a hole in the top or bottom plate of the wall to get the wire into the room walls. This will accept some special tools such as an electrical fish tape, electrical boxes and then on.

Here are the most pop options for running speaker wire:

• Running speaker wire under carpet; meet Wire & Cablevision

• Running speaker wire through the attic

• Running speaker wire in crawl space or basement

• Calling an electrician and having them run your cabling

Running speaker wire nether carpeting being probably the easiest solution; nosotros will discuss this first. You may need a fish tape to consummate this project successfully.

Cut a small slit through both the carpet and the padding underneath. Run the fish wire under both carpet and the padding. Utilise a fish tape and a helper to guide the fish record from the opening to the desired location. It may be necessary on longer runs to make several slits to guide the wire along the path you wish it to run. Take your time getting the tape to the desired location. Once you take reached your end point location pull the record out and wrap the wire effectually the fish record loop and tape it so that it will not snag when you lot pull it back through.

Carefully pull the record and the connected speaker wire back to the get-go point where you inserted the fish tape.

Running speaker wire through the attic is pretty elementary too, but you may need to drill holes into the elevation plate of the wall. You will besides need a hole in the wall to become the wire back into the room. Provided y'all practice not take any stop plates that continue the wire from falling down the wall so it can exist accessed from the wire termination hole in your room. More near that in a bit…

Information technology is easiest to drill holes in both height plates of both walls that the wire will be running down. You will also demand a speaker wire termination box, I normally employ a standard electric box for this. Cutting the electrical box hole into the wall at the same altitude from the floor that other electrical boxes are in your room. Utilize the electrical box equally a template, and then cut the hole into the walls both at the entrance and end point where the wire needs to come out.

Don't put the electric box in the wall until after you have run the wires. You can pretty easily accomplish your manus in the wall and pull it out subsequently it has been run downwardly into the wall from the attic. If you accept insulation in the walls, this projection will be a footling tougher and take some boosted patience. See the following to consummate this step.

Get-go in the attic, make sure the wire is long plenty to run the length of the run you demand plus to go down both walls to go to your desired location. (Y'all will have to locate the top plate of the wall inside the attic earlier drilling the holes) Make sure to leave plenty of wire and then you tin can easily bring the wire out of the hole, yous can e'er cut the wire shorter later. You tin can even utilise some special speaker wire termination plates that are made to mount right to the electric box.

These tin can exist found at nearly any home supply builders shop such as Lowes or Home Depot. Y'all can probably become the speaker wire at the same store too if you wish or you can social club it through Parts Express Tools & Tech Aids – Installation tools, examination equipment, speaker repair and replacement tools too.

Running speaker wire through a crawl space is a good selection for hiding speaker wire (if you have a clamber infinite under the floor of your home theater room).

The method is the same equally running the wire through the attic mentioned in a higher place.

The difference being you will need to find the bottom plate of the walls from the clamber space. This location is about easily found past locating nails that are sticking out of the floor, (showing the sharp part of the nails where yous tin can see them looking upwardly at the floor from the crawl space) there would be bare nails running in a line where the bottom plate was nailed into the flooring.

Having an electrician run your speaker wire is obviously the easiest but also the well-nigh expensive of your options. Nonetheless, for many home sound enthusiasts this option is going to be the about attractive. A proficient electrician will take no trouble finding your walls and running the cabling. They are used to this blazon of retrofit installation and accept all the tools necessary for the chore.

Speaker wire connections

At present that you have the wires run, you can tackle the like shooting fish in a barrel office. Here you may also need some specialized tools and what you need volition largely depend on what type of wire you are using and the connector types you need.

Below are some tools you may demand to complete the tasks above:

• Wire strippers

• Electrical record (for fishing wires)

• Connectors to stop the speaker wires, such as assistant plugs, spades or whatever speaker wire connectors you plan to use. Connectors – 1 of the largest selections of connectors online for habitation, machine and professional audio

• A soldering iron may be necessary if y'all wish to solder your connectors. This offers the nearly long term and stable connection type. Spiral connectors tin can work themselves loose over fourth dimension. Tools & Tech Aids – Installation tools, examination equipment, speaker repair and replacement tools

• Spiral drivers

• Wire cutters

• Crimpers

• Speaker wire connexion plate or speaker wire plug in plates to give attractive wall appearance

See the Parts Limited Tools & Tech Aids – Installation tools, test equipment, speaker repair and replacement tools

Get back to the pinnacle of folio!

Render to

Return to best speaker wire page from; running speaker wire page.

Return to Home Speaker from;

Render to Abode Page – Home Speaker from; running speaker wire

Other helpful home audio cabling manufactures

bi wire speaker cables
best speaker wire
speaker wires
audio cable connectors
12-guage-speaker-wire
14-guage-speaker-wire
diy speaker wire
HDMI audio video cables

Parts Express – WBT Audio Connectors